9631 |
88-1
|
研究報告
|
康尚文
教授
|
微冷卻晶片陣列系統內之微結構層接合技術
|
9632 |
84-1
|
研究報告
|
康尚文
教授
|
微光學平板熱壓成形技術研究
|
9633 |
97-2
|
期刊論文
|
吳乾埼
副教授
|
Manufacture of a polyaniline nanofiber ammonia sensor integrated with a readout circuit using the CMOS-MEMS technique
|
9634 |
97-1
|
期刊論文
|
洪祖昌
教授
|
微衛星電腦系統之即時功能與飛行軟體設計
|
9635 |
97-2
|
期刊論文
|
洪祖昌
教授
|
Thermal conductivity modeling of compacted type nanocomposites
|
9636 |
95-2
|
期刊論文
|
洪祖昌
教授
|
微衛星TUUSAT-1電源次系統設計分析與試驗
|
9637 |
91-1
|
期刊論文
|
洪祖昌
教授
|
Imagery Payload Design for Passive Magnetically Stabilized Microsatellite
|
9638 |
92-2
|
期刊論文
|
洪祖昌
教授
|
Mission and constellation design for low-cost weather observation satellites
|
9639 |
96-1
|
期刊論文
|
洪祖昌
教授
|
Fluid Dynamics and Heat Transfer Analysis of Three Dimensional Microchannel Flows with Microstructures
|
9640 |
95-1
|
期刊論文
|
洪祖昌
教授
|
Comparison of 3-D and 2-D DSMC Heat Transfer Calculations of Low-Speed Short Microchannel Flows
|
9641 |
95-1
|
期刊論文
|
洪祖昌
教授
|
微衛星發展歷史與現況
|
9642 |
96-1
|
期刊論文
|
洪祖昌
教授
|
微衛星低成本重力梯度桿設計分析
|
9643 |
91-1
|
期刊論文
|
趙崇禮
教授
|
Friction and wear behaviour of TiN/Au, TiN/MoS2 and TiN/TiCN/a-C:H coatings
|
9644 |
91-1
|
期刊論文
|
趙崇禮
教授
|
Ductile behaviour in single-point diamond-turning of single-crystal silicon
|
9645 |
96-1
|
期刊論文
|
趙崇禮
教授
|
Recent developments on microablation of glass materials using excimer lasers
|
9646 |
95-1
|
期刊論文
|
趙崇禮
教授
|
Investigation of Toughness and Wear Resistance of a-C/a-C:Cr Multilayer Coatings
|
9647 |
91-1
|
期刊論文
|
林逢傑
助理教授
|
A digital current control technique for voltage-fed induction motor drives
|
9648 |
89-2
|
期刊論文
|
林逢傑
助理教授
|
Estimation of Velocity from Discrete Position Measurements Using Fuzzy Logic Observer
|
9649 |
91-2
|
期刊論文
|
林逢傑
助理教授
|
Adaptive fuzzy logic-based velocity observer for servo motor drives
|
9650 |
93-1
|
期刊論文
|
林逢傑
助理教授
|
開關磁阻馬達之轉矩與徑向力模型建立與控制
|
9651 |
93-1
|
期刊論文
|
林逢傑
助理教授
|
Micro-stepping control of a two-phase linear stepping motor with three-phase VSI inverter for high-speed applications
|
9652 |
91-2
|
期刊論文
|
林逢傑
助理教授
|
On-line tuning of an efficiency-optimized vector controlled induction motor drive
|
9653 |
94-1
|
期刊論文
|
李經綸
副教授
|
Application of FSQP to Inverse Estimation of the Constitutive Constants and Friction Coefficient in the Nosing Process
|
9654 |
94-2
|
期刊論文
|
李經綸
副教授
|
Application of ANFIS for inverse prediction of hole profile in the square hole bore-expanding process
|
9655 |
92-1
|
期刊論文
|
李經綸
副教授
|
Study of ductile fracture and preform design of upsetting process using adaptive network fuzzy inference system
|
9656 |
94-1
|
期刊論文
|
李經綸
副教授
|
Study of using ANFIS to the prediction in the bore-expanding process
|
9657 |
87-2
|
期刊論文
|
李經綸
副教授
|
An elasto-plastic finite-element analysis of the metal sheet redrawing process
|
9658 |
89-2
|
期刊論文
|
李經綸
副教授
|
A study of the optimum blank for square cup drawing using the streamline method
|
9659 |
86-2
|
期刊論文
|
李經綸
副教授
|
Influence of Lubricant on Limit Drawing Ratio in Cup-Drawing Process: A Stabilization Matrices Scheme
|
9660 |
83-2
|
期刊論文
|
史建中
教授
|
Weighting objectives strategy in multicriterion fuzzy mechanical and structural optimization
|